Produktblad
Snabbstarts guide
Manual
Switch rekommend.
Applikations diagram

The NetworkHD™ 100-Series is a matrix-based H.264 HD over IP AV distribution platform. With its simple system configuration and robust feature set, it provides the best value in networked video distribution, without compromising quality.
The NHD-100-RX H.264 decoder is intended for use with an NHD-100-TX H.264 encoder (sold separately) to provide a complete end-to-end streaming system.

Key Features:

  • Highly scalable, high quality low-bandwidth solution using the most efficient compression technologies to allow for very large commercial AV deployments
  • Streams HDMI over IP networks
  • Plug and Play setup with quick networking configuration and auto discovery of components
  • Quick Sync™ technology for virtually instantaneous seamless switching
  • Full RS232 control of connected displays and CEC One-Touch Play
  • Major control systems drivers available including the WyreStorm Enado™ Control System

Features

  • For use with the NHD-100-TX H.264 encoder to provide a complete end-to-end streaming system
  • Features 1 x LAN (PoE) input to 1 x HDMI output
  • Provides streaming output via Ethernet port
  • Supports input signal resolution up to 1920 x 1200@60Hz
  • Highly scalable, high quality low-bandwidth solution using the most efficient compression technologies to allow for very large commercial AV deployments
  • Plug and Play setup with quick networking configuration and auto discovery of components
  • Quick Sync™ technology for virtually instantaneous seamless switching
  • Full RS232 control of connected displays and CEC One-Touch Play
  • Major control systems drivers available including the WyreStorm Enado™ Control System
  • Supports video previewing on a PC or third party device. Capable of outputting two simultaneous IP streams. One large IP stream supports a streaming resolution from 480p @ 60Hz to 1920 x 1200 @ 60Hz to view a video on the decoder. The other small one supports resolutions of 352 x 288 @ 5Hz to easily preview a video from the encoder on a PC or Mac
  • Use with the new NetworkHD controller (NHD-000-CTL) for matrix control and management via the LAN, as well as for allowing control from third party control system such as AMX, Crestron, Control4, RTI & Enado.
  • Supports PoE to be remotely powered from the switch by compatible power source equipment, eliminating the need for a nearby power outlet
  • Standards-based H.264/MPEG-4 AVC video compression
  • Full PC control suite available free of charge at wyrestorm.com
  • Supports HDCP
  • Supports the H.264 features baseline profile, main profile and high profile
  • Auto input format detection
  • Configurable encoding bit rate up to 40 Mbps
  • Supports AutoIP, zero-configuration networking (zeroconf), a set of technologies that automatically assigns dynamic IP addresses to the Encoder on start-up and a server-less method of choosing IP addresses

In the Box:
1 x NHD-100-RX Main Unit
1 x Power Adapter (12V 1A DC)
1 x Detachable Plug
3 x Phoenix Conn. (Male, 3.5 mm, 3 pins
2 x Mounting Brackets
1 x Quickstart Guide



General

Extender type
Reciever (Rx)
Technology
H.264

Video specifications

Max supported resolution
1920x1200 8bit
Refresh rate
60 Hz
Scaler
Ei

Connections

Video in
IP stream (RJ-45)
Video out
HDMI
Audio inputs
3,5mm tele
Audio outputs
Euroblock line
Control
Ethernet/IP (RJ-45)
Control
RS-232 3-pin Phoenix
USB passthrough
Ei

Communication

Latency
60 ms About 60 ms-90 ms (Low latency mode), About 250 ms-300 ms (High quality mode)

Energy

Power Supply
12V 1A DC

Mitat ja Paino

Width
200 mm
Depth
94 mm
Height
25 mm
Net weight
0,48 kg

Additional information

Installation
Freestanding/Shelf
Included Accessories
1 x NHD-100-RX Main Unit 1 x Power Adapter (12V 1A DC) 1 x Detachable Plug 3 x Phoenix Conn. (Male, 3.5 mm, 3 pins 2 x Mounting Brackets

Paketin tiedot

Paketin mitat
319 x 182 x 81 mm
Paketin paino
1,03 kg